BMW K 1200RS Repair Manual Download

Page: 99 / 416

11.13

1100

Disassembling engine

Removing, disassembling and assem-
bling combined oil-water pump

Removing the oil/water pump

•

Disconnect oil pressure warning and water pump
temperature sensor cables from switch.

•

Withdraw cables through hole in pump housing.

•

Remove pump housing cover (10) and loosen
the gasket by tapping lightly a plastic-faced ham-
mer.

•

Remove the housing and loosen the gasket by
tapping lightly with plastic-headed hammer.

•

Pull off the oil pump gearwheel and the oil pump
intermediate flange.

Disassembling the oil/water pump

•

Clamp the pump housing into a vise at the seal-
ing faces, using soft jaws.

•

Remove water pump impeller (9), holding pump
shaft (5) to prevent it from turning.

•

Take off the water pump impeller with spacing
bushing (8).

•

Press out pump shaft (5).

•

Examine the pump housing for damage.

Removing slipring seal and shaft sealing ring

•

Drive out slipring seal (7) and shaft sealing
ring (6) with a drift,

BMW No. 11 6 721

Removing the oil pressure relief valve

•

Unscrew plug (1) and take out spring (3).

•

Pull valve piston (4) out with a magnet and exam-
ine it for damage.

Installing the oil pressure relief valve

•

Oil valve piston (4) lightly before installing.

•

Insert spring (3) and tighten the screw plug with
a new seal (2).

Tightening torque:

Oil pressure relief valve screw plug .............. 35 Nm

KR110420

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands