BMW K 1200RS Repair Manual Download Page 163

Page: 163 / 416

13.13

13 63

Replacing and adjusting throt-

tle-valve potentiometer

–

Remove throttle-valve rail.

•

Remove the fasteners (arrows). Remove the
throttle-valve potentiometer.

•

Install the new throttle-valve potentiometer.

Note:

throttle-valve actuator must be installed and con-
nected. Throttle-valve potentiometer must be con-
nected.

•

Connect

BMW

MoDiTeC to diagnosis plug be-

neath front seat.

•

Open the TOOLBOX menu and select THROT-
TLE-VALVE POTENTIOMETER or throttle-valve
actuator.

•

Follow the instructions of the

BMW

MoDiTeC.

•

Tighten screws securing throttle-valve potenti-
ometer.

•

Perform function test with

BMW

MoDiTeC, menu

item THROTTLE-VALVE POTENTIOMETER or
throttle-valve actuator.

•

Apply sealing lacquer to securing screws.

•

Installation is the reverse of the removal proce-
dure.

Tightening torque:

Screws, throttle-valve potentiometer
(clean t Loctite 243) .......................... 2 Nm

13 00

Basic throttle cable setting

(

00.36)

KR130160

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Brands by name

Popular brands