BMW K 1200RS Repair Manual Download | Manualshive

Page: 361 / 416

background image

46.27

–

Remove the rear left footrest holder (

a

46.23)

•

Remove the fasteners for the battery carrier, and
remove the rear brake fluid reservoir, brake hos-
es and battery carrier together with the pressure
modulator.

•

Disconnect the plugs for the gear indicator
switch, temperature sensor at cylinder head,
side stand switch and oxygen sensor, and guide
the cables through downwards.

•

Disconnect the earth (ground) lead at the upper
cross-tube and the leads at the alternator and
starter motor.

–

Remove rear cross-tube (

a

46.25).

–

Remove clutch slave cylinder (

a

21.9).

•

Guide the clutch line through upwards.

•

Separate the plug connectors for the left/right
handlebars.

•

Remove the left handlebar with multifunction
switch, together with the holder for the left radia-
tor, the clutch line and the clutch slave cylinder.

•

Remove the right handlebar with multifunction
switch.

•

Disconnect the plug of the front ABS sensor.

•

Detach the electronic equipment box and the
wiring harness from the frame (arrows) and re-
move.

–

Remove the telescopic fork with the front wheel
(

a

31.5).

L

Note:

Make sure that oil cannot escape from the telescop-
ic fork.

–

Remove fork bridge (

a

31.9).

–

Remove front suspension strut (

a

31.15).

•

Tie the leading link up to the frame.

•

Detach the cross-member from the frame at left
and right.

•

Release the gearbox fasteners from the frame,
holding at the left to prevent from turning.

e

Important:

Make sure that clearance between gearbox and
frame at the right is correct.

•

Lift the frame with leading link clear of the other
components.

•

Remove mounted parts.

KR460430

KR460880

«
...
359
360
361
362
363
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: Graphite Pages: 44

Powersports CT200U

Brand: Coleman Pages: 37

TXT PRO - PART LIST 2010

Brand: GAS GAS Pages: 64

Tear-off machine

Brand: Allstar Pages: 4

Brand: R&G Pages: 18

Brand: Eastwood Pages: 8

Brand: Protos Pages: 6

TOPMASTER MOVIL V0X814ST

Brand: Shad Pages: 2

Brand: Saddlemen Pages: 2

Brand: VOIGT MT Pages: 2

Brand: Voigt Pages: 2

Brand: Benelli Pages: 55

Brand: Benelli Pages: 65

Brand: Benelli Pages: 75

Brand: APRILIA Pages: 475

Brand: Honda Pages: 183

Goldwing GL1200L 1985

Brand: Honda Pages: 165

Brand: Bajaj Auto Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands