BMW K 1200RS Page 416 Repair Manual Download

Page: 416 / 416

63.7

63 21

Renewing rear lights

63 21

Removing/installing rear/brake

light housing

•

Release the fasteners (1) and pull the rear/brake
light housing (2) off to the rear.

•

Remove bulb with holder from rear/brake light
housing.

•

Installation is the reverse of the removal proce-
dure.

63 23

Removing/installing turn indicator

housing

•

Release the fastener (5) and take off the turn in-
dicator glass (3).

•

Pull off the cable connectors.

•

Release fastener (6) and remove cover (7).

•

Release the fastener (8).

•

Pull off the flashing turn indicator (4).

•

Installation is the reverse of the removal proce-
dure.

63 99

Renewing bulb

Note:

Never touch the glass of the bulb with the fingers.

•

Take off the appropriate housing. Change the
bulb.

Important:

When changing the rear and brake light bulbs, do
not accidentally confuse their contacts.

Cable colours at contacts

grey-yellow (1)
brown (2)
grey-black (3)

KR630031

KR630070

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands