BMW K 1200RS Repair Manual Download

Page: 72 / 416

00.63

16 00

Renewing fuel filter

(every 40,000 km/24,000 miles)

(Inspection III)

Note:

If the fuel is of poor quality, replace the fuel filter eve-
ry 20,000 km (12,000 miles).

–

Remove fuel tank (

16.5).

Warning:

Comply with safety precautions when handling or
working with fuel.

•

Drain fuel tank.

16 00

Removing/installing fuel-pump

unit

•

Remove seal (6) and union nut (7).

•

Pull fuel pump unit (5) far enough out of the fuel
tank to enable the clips on drain hose (3) and
breather hose (4) to be undone with pliers.

•

Pull off the hoses.

•

Remove fuel pump unit (5) completely, with
gasket (6).

K41160020

16 1 710

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands