BMW K 1200RS Repair Manual Download | Manualshive

Page: 127 / 416

background image

11.41

1100

Installing piston with conrod

•

Turn the relevant crankpin to bottom dead
centre.

•

Make sure all pistons and conrods are of the
same weight classes (

a

11.25).

e

Important:

Note the pin for the 2nd piston ring gap.

•

Space the piston ring gaps at approx. 120° off-
sets.

•

Thoroughly oil the piston rings, piston skirt and
cylinder wall.

•

Insert the piston into the sliding sleeve,

BMW No. 11 6 700

.

•

The arrow on the piston crown must point to-
wards the timing end of the engine (cylinder 1).

•

Insert the piston with conrod into the cylinder un-
til the sliding sleeve is touching the crankcase.

•

Carefully push the piston by hand out of the
sleeve and into the cylinder.

1100

Installing big end bearings

e

Important:

Do not accidentally interchange conrods or bearing
shells. Take great care to reinstall the bearing shells
in their original positions. Always use new big end
bolts.

•

Turn the crankpin of the relevant cylinder to bot-
tom dead centre.

•

Oil the crankpin and seat the conrod against it.

•

Place the big-end bearing cap in position and
tighten the screws to the specified torque.

•

Use an angle-of-rotation gauge,

BMW No. 11 2 500

, to tighten the big end bear-

ings.

X

Tightening torque:

Split conrod bearings ................................... 20 Nm
Additional angle of rotation................................ 80°

1100

Measuring big end bearing play

•

Unscrew and remove the bearing cap and clean
the crankpin and bearing cap to remove oil.

•

Measure bearing play with Plastigage,

BMW No. 00 2 590

.

•

Place the Plastigage strip (arrow) over the entire
bearing width and 6 to 8 mm
(0.2362 to 0.3150 in) away from the centre of the
crankpin.

KR110620

11 2 500

KL110180

«
...
125
126
127
128
129
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: National Cycle Pages: 3

Brand: AGV Pages: 45

Brand: TRS Pages: 38

Brand: Takegawa Pages: 2

Windscreen N20012A

Brand: VStreamT Pages: 3

Brand: Honda Pages: 143

Brand: Vance and hines Pages: 5

Brand: Honda Pages: 98

Brand: DYNATEK Pages: 4

Brand: DYNATEK Pages: 12

Brand: Shark Pages: 80

Brand: Race Dynamics Pages: 25

Brand: SHERCO Pages: 54

Brand: KYMCO Pages: 68

Brand: KYMCO Pages: 229

Brand: KYMCO Pages: 433

Brand: Brixton Pages: 49

Brand: VESPA Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands