BMW K 1200RS Repair Manual Download Page 112

Page: 112 / 416

11.26

1100

Removing/installing crankshaft

gear and rotor flange

•

Prevent from turning with retainer,

BMW No. 11 2 800,

(see right).

•

Remove the screw (arrow) for the crankshaft
sprocket and the rotor flange.

•

Pull off rotor flange (1) with light hammer-blows,
and take off the sprocket.

•

Install the crankshaft sprocket first, then tighten
the rotor flange.

Tightening torque:

Rotor flange ................................................. 50 Nm

1100

Measuring backlash at the coun-

tershaft

. Note:

Abnormal noises, especially at low engine speeds,
could be due to excessive backlash between the
crankshaft/countershaft gearing.

. Important:

Always measure backlash with the engine cold.

–

Remove alternator (

12.10).

•

Secure dial-guage holder,

BMW No. 00 2 500

to gearbox intermediate flange.

•

Use the clamping screw to secure the clamp,

BMW No. 11 5 510

, to the first vane of the driver.

•

Adjust the dial gauge,

BMW No. 00 2 510

, such

that the mark on the tool (3 mm from outside
edge) is aligned with the needle of the dial gauge
on the reference face.

•

Move the driver by hand. Note dial-gauge read-
ing.

•

Remove the clamp,

BMW No. 11 5 510

•

Turn the crankshaft to turn the driver through
120°.

•

Secure the clamp to the second driver vane and
use the dial gauge to measure the backlash.

•

Take a third measurement.

•

Calculate the average over the three measured
values.

•

Replace the countershaft if the average obtained
from the three measurements is at least 0.03 mm
(0.0012 in).

KR110410

Determining countershaft

Average of 3 measure-
ments

Colour
code

Stage

0.03 mm ... 0.06 mm
(0.0012 in...0.0024 in)

green

- 0.040 mm
(- 0.0016)

greater than 0.06 mm
(0.0024 in)

yellow

- 0.080 mm
(-0.0032 in)

Kr111100

11 5 510

00 2 500

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Brands by name

Popular brands