manualshive.com logo in svg

BMW K 1200RS, Repair Manual

Share
Download
BMW K 1200RS Repair Manual Download Page 266

32.8

32 72 

Removing/installing brake lever 

fitting

–

Take off mirror (

a 

00.22).

–

Remove grip tube (

a 

32.6).

e

 Important:

Do not allow brake fluid to come into contact with 
painted parts of the motorcycle, because brake fluid 
destroys paint.

–

Drain the brake system (

a 

34.16).

•

Disconnect brake line (1) from brake lever 
fitting (2).

•

Disconnect Bowden cable (3) at adjusting 
screw (4) of brake lever fitting (2).

•

Remove cover (5) from brake lever fitting (2).

•

Remove brake light switch (6) from brake lever 
fitting (2).

•

Loosen fastener (arrow) for brake lever fitting (2) 
at handlebar tube (7).

•

Pull brake lever fitting (2) off handlebar tube (7).

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following:

e

 Important:

Make sure that lines and cables are correctly routed.

L

 Note:

Note correct installed position of brake light 
switch (6).

•

Align the marks on brake lever fitting (2) and han-
dlebar tube (7) (arrow).

•

Tighten brake lever fitting (2).

–

Add brake fluid and bleed 
(

a 

00.51).

–

Basic throttle cable setting (

a 

00.36)

X 

Tightening torque:

Fastener for brake lever fitting ........................ 6 Nm
Line to fitting ................................................ 18 Nm
Mirror ........................................................... 20 Nm

K41320020

1

2

3

5

7

6

4

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands