BMW K 1200RS Page 122 Repair Manual Download

Page: 122 / 416

11.36

Installing dampers

•

Insert the rubber dampers (7) into the damper
housing (6).

Note:

New parts must be oiled lightly.

•

Push the retaining plate (4) onto the output
shaft (3), slightly heat the inner part of the
damper (5) and press it into position on the shaft.

•

Push the damper housing on to the output shaft.

1100

Assembling engine

Installing output shaft

•

Push on circlip (2) and needle roller race (1).

•

Place the output shaft in the crankcase.

Note:

Make sure that the gap of the circlip (arrow) is facing
downward in the crankcase.

•

Install O-rings (8, 9) for the water and oil passag-
es.

Assembling the crankcase

•

Check that sealing face is clean and degreased
and apply a thin coat of

Omni VISC 1002

, see

line on sealing face with grey shading.

•

Fill the expansion groove (arrow) with sealing
compound.

Note:

Scrape off excess sealant with a spatula.

KR110451

KR110521

KL110250

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands