BMW K 1200RS Repair Manual Download | Manualshive

Page: 30 / 416

background image

00.21

00 00

Unpacking the motorcycle

•

Lever off the cover.

•

Cut the plastic sheet open and pull it off.

•

Take out the separate pack of items:

–

Windscreen

–

Mirrors, right/left

–

Engine spoiler

–

Small parts/fasteners

•

Force off cross-struts with a suitable lever.

e

Attention:

Do not knock the cross-struts out or the motorcycle
may be damaged.

•

Remove the end-walls.

•

Remove the side-walls.

e

Attention:

Remove any nails projecting from the base of the
packing or lying on the base or on the floor.

•

Open the tensioning straps.

e

Attention:

Make sure that the tensioning straps cannot fly out
and cause injury when they are opened.

•

Push the motorcycle off the pallet.

•

Dispose of the packing materials in an environ-
mentally responsible manner as described in Cir-
cular No. 23/91 - Sales.

General instructions

Pushing the motorcycle onto a work-
shop platform

d

Warning:

[Integral ABS] Take care on account of residual
braking function.
Wait until self-diagnosis completes and, with ignition
switched on, push the motorcycle onto the platform.
The brake booster is active.

00 00

Inspecting motorcycle for dam-

age

•

Check for damage.

•

“Express message” to
BMW Motorrad, UX-VS-1
Fax number

089-382-33220

•

Rectify the fault.

•

If parts are needed, order them by using the
electronic parts list.

•

Costs are to be processed by the warranty claim
system (stage 4). Defect codes:

–

Parts missing

10 01 00 00 00

–

Parts damaged

10 02 00 00 00

–

Incorrect parts delivered

10 03 00 00 00

•

If the parts are not in the Electronic Parts Cata-
log, please contact Parts Service.

00 00

Checking that delivery is com-

plete

•

Turn key in seat lock to left and hold it there.

•

Pull the seat upwards and to the rear out of its
catch, as far as the first detent position.

•

Remove seat.

•

Check that the delivery is complete:

–

Separate pack of items

–

Keys

–

All optional extras

–

Toolkit (see the illustration of the contents on the
inside of the toolkit bag)

–

Documentation (open the cover on the underside
of the seat)

«
...
28
29
30
31
32
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: Kabuto Pages: 25

Brand: kellermann Pages: 2

SIDE FORCE 445cc

Brand: Mash Pages: 27

Nils Extreme MTW03

Brand: Abisal Pages: 21

Brand: Honda Pages: 3

Brand: KTM Pages: 38

Brand: Honda Pages: 140

Brand: Denali Pages: 5

Brand: GAS GAS Pages: 32

Brand: Big Bike Parts Pages: 3

Brand: MRA Pages: 6

Brand: LSL Pages: 4

BRUTALE 750 ORO

Brand: MV Agusta Pages: 386

Brand: Kenwood Pages: 36

Brand: Kenwood Pages: 97

Brand: hepco & becker Pages: 3

Brand: hepco & becker Pages: 3

H-NAPE CHINSTRAP

Brand: Fast Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands