background image

L4

December ’13 (TK) 21

99505-01134-01E

© COPYRIGHT SUZUKI MOTOR JAPAN

FOREWORD

This motorcycle has been designed and produced utilizing Suzuki’s most modern
technology. The finest product, however, cannot perform properly unless it is cor-
rectly assembled and serviced. This set-up manual has been produced to aid you in
properly assembling and servicing this motorcycle.

Please read this manual and follow its instructions carefully. To emphasize special
information, the symbol 

 and the words 

WARNING

CAUTION

NOTICE

 and

NOTE

 have special meanings. Pay particular attention to messages highlighted by

these signal words:

Indicates a potential hazard that could result in death or serious injury.

Indicates a potential hazard that could result in minor or moderate injury.

Indicates a potential hazard that could result in motorcycle or equipment
damage.

NOTE:
Indicates special information to make maintenance easier or instructions clearer.

This set-up manual is based on a motorcycle of standard specification. Some minor
differences from this manual may be found in other specifications.

Summary of Contents for DL1000AL4



























Reviews: