Infineon XDPP1100 Technical Reference Manual Download Page 399

Page: 399 / 562

User Manual 399 of 562 V 1.0

2021-08-25

XDPP1100 technical reference manual

Digital power controller

Central processing unit subsystem

a system point of view, it needs to be mitigated, for example by copying the OTP program onto the RAM and
executing it from the RAM.

15.4.3.6

OTP module registers

The relevant OTP-related registers and their descriptions are provided in

Table 101

OTP module-related register description

Register name Field name

Access Address

Bits

Description

STAT

PWR_STAT

5002_0000h [0]

OTP power status.
0: OTP power off
1: OTP power on

STAT

BUSY

5002_0000h [4]

Instruction status.
0: Completed
1: Busy

STAT

CMP_STAT

5002_0000h [8]

Compare status (valid after direct
access compare instruction).

STAT

PRECH_STAT

5002_0000h [9]

Precharge status (valid after direct
access compare instruction).

STAT

RD1_FL

5002_0000h [16]

READ1 fail indicator.
0: No READ1 failure during
programming
1: READ1 failure during
programming

STAT

RD2_FL

5002_0000h [17]

READ2 fail indicator.
0: No READ2 failure during
programming
1: READ2 failure during
programming

STAT

SOAK_FAIL

5002_0000h [18]

SOAK fail indicator.
0: No SOAK failure during
programming
1: SOAK failure during
programming

STAT

SOAK_CNT

5002_0000h [24]

Max. SOAK counter. For debug in
case any of the bits requested to be
programmed had to be soaked.

CONF

PWRUP

5002_0004h [0]

OTP power command.
0: Power-down OTP
1: Power-up OTP

CONF

AHB_CLK_RATIO

5002_0004h [5:4]

AHB clock ratio with respect to the
OTP kernel clock (25 MHz).
0: AHB = 100 MHz
1: AHB = 50 MHz
2: AHB = 25 MHz

Summary of Contents for XDPP1100



















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for XDPP1100

Reviews:

Brands by name

Popular brands

Infineon XDPP1100, Technical Reference Manual

Search results

Summary of Contents for XDPP1100

Reviews:

Brands by name

Popular brands