manualshive.com logo in svg

Infineon XDPP1100, Technical Reference Manual

Share
Download
Infineon XDPP1100 Technical Reference Manual Download Page 339

  

 

User Manual                                                                                                            339 of 562                                                                                                                      V 1.0  
 

 

2021-08-25 

XDPP1100 technical reference manual 

Digital power controller 

Central processing unit subsystem  

 

 

Register name  Field name 

Access  Address 

Bits 

Description 

CPUS_CFG_SE
T 

EN_AUX_EXTWKUP  W 

4000_0004h  [20] 

Enable auxiliary external wakeup 
source to wake up CPUS when in 
the power-down or hibernate state. 
0: No change to existing value 
1: CPUS EXT-3 wakeup source is 
enabled 

CPUS_CFG_SE
T 

EN_PMBUS_WKUP 

W 

4000_0004h  [21] 

Enable internal source PMBUS_IRQ 
to wake up CPUS when in the 
power-down or hibernate state. 
0: No change to existing value 
1: CPUS PMBUS_IRQ wakeup 
source is enabled 

CPUS_CFG_SE
T 

EN_GPIO0_WKUP  

W 

4000_0004h  [22] 

Enable internal source GPIO0_IRQ 
to wake up CPUS when in the 
power-down or hibernate state. 
0: No change to existing value 
1: CPUS GPIO0_IRQ wakeup source 
is enabled 

CPUS_CFG_SE
T 

EN_GPIO1_WKUP 

W 

4000_0004h  [23] 

Enable internal source GPIO1_IRQ 
to wake up CPUS when in the 
power-down or hibernate state. 
0: No change to existing value 
1: CPUS GPIO1_IRQ wakeup source 
is enabled 

CPUS_CFG_CL
R 

SET_REMAP 

W 

4000_0008h  [0] 

This bit controls the remap signal 
used to change the address map 
implemented by the bus matrix. 
0: No change to existing value 
1: Remap signal set to 0 

CPUS_CFG_CL
R 

DS_DBGPORT 

W 

4000_0008h  [2] 

Disable debug port. 
0: No change to existing value 
1: DBG port connection is disabled 

CPUS_CFG_CL
R 

EN_EXTWKUP 

W 

4000_0008h  [3] 

Enable external wakeup (WKUPIN) 
when the CPUS is in the hibernate 
state. 
0: No change to existing value 
1: CPUS external wakeup is 
disabled 

CPUS_CFG_CL
R 

USR_CNFG0 

W 

4000_0008h  [4] 

Reserved 

CPUS_CFG_CL
R 

USR_CNFG1 

W 

4000_0008h  [5] 

Reserved 

CPUS_CFG_CL
R 

USR_CNFG2 

W 

4000_0008h  [6] 

Reserved 

Summary of Contents for XDPP1100



















































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands