manualshive.com logo in svg

R&S ZNC3, Руководство пользователя

Пользовательский мануал R&S ZNC3 доступен для бесплатного скачивания на нашем сайте. Изучайте функциональные возможности этого продукта и получайте всю необходимую информацию для его использования. Скачать мануал можно на manualshive.com.

Поделиться
Скачать
background image

GUI Reference

R&S

®

 ZNC

280

User Manual 1173.9557.02 ─ 13

Image Suppr.

The "Image Suppr." settings define whether the analyzer measures with a local oscillator
frequency LO below or above the RF input frequency. This feature can be used to elim-
inate known spurious components in the input signal that can distort the measurement,
especially in the low frequency range.

●

In "Auto" mode, the analyzer auto-selects the local oscillator frequency, depending
on the receiver (RF) frequency and the test port. This mode systematically avoids
known spurious signals provided that no frequency conversion occurs in the test
setup.

●

"LO > RF" means that the LO frequency is always above the measured RF frequency.
This mode is appropriate for avoiding single, known spurious signals.

●

"LO < RF" means that the LO frequency is always below the measured RF frequency.
This mode is appropriate for avoiding single, known spurious signals.

Tip:

 In the presence of several spurious signals, setting the "Image Suppr." parameter

globally may not be sufficient. To improve the result, perform a "Segmented Fre-
quency" sweep and assign independent LO frequencies to the individual sweep seg-
ments.

Application example

Consider the following test setup with strongly reflecting DUT (e.g. a bandpass in its stop
band) that is measured in transmission. a

1

 is generated at a frequency RF. The reflected

wave b

1

 falls into the receiver mixer of the analyzer port 1, where a small fraction of the

mixer product RF + 2*IF can be reflected back towards the DUT. If this spurious wave
a'

1

 passes the DUT, then it is received as b'

2

 at port 2, together with the wanted signal

b

2

.

LO > RF implies that LO = RF + IF. The mixer at port 2 converts both the wanted signal
b

2

 and the spurious signal b'

2

 which is at the frequency RF' = IF + LO, to the same IF

frequency. The response of an ideal, infinitely steep bandpass filter with a pass band
between B

-

 and B

+

 looks as follows:

For a wide bandpass, the spurious response flattens the filter edges.

Channel Settings

Содержание ZNC3




























































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZNC3

Oldham BM25 Operating Manual preview
BM25
Бренд: Oldham Страницы: 43
Kane 400 Quick Reference Manual preview
400
Бренд: Kane Страницы: 4
Unico SQ Series Service Manual preview
SQ Series
Бренд: Unico Страницы: 96
Keithley 610C Instruction Manual preview
610C
Бренд: Keithley Страницы: 44
Keithley 2651A User Manual preview
2651A
Бренд: Keithley Страницы: 76
Keithley 4200-SCS Startup Manual preview
4200-SCS
Бренд: Keithley Страницы: 12
Keithley 194 Instruction Manual preview
194
Бренд: Keithley Страницы: 281
M-Sure MS-535 Series Quick Start Manual preview
MS-535 Series
Бренд: M-Sure Страницы: 2
J-TECH Solar Auxiliary Power Unit Operator'S Manual preview
Solar Auxiliary Power Unit
Бренд: J-TECH Страницы: 6
Lumel NA3 User Manual & Quick Start preview
NA3
Бренд: Lumel Страницы: 32
GREISINGER GOX 91 Brief Operating Manual preview
GOX 91
Бренд: GREISINGER Страницы: 4
SMPE MAFS010 Instructions preview
MAFS010
Бренд: SMPE Страницы: 2
Bird Electronic Thruline 4020 Series Instruction Book preview
Thruline 4020 Series
Бренд: Bird Electronic Страницы: 59
Endress+Hauser Proline Promass 200 Safety Instructions preview
Proline Promass 200
Бренд: Endress+Hauser Страницы: 12
Eplus BL-H1 Instruction Manual preview
BL-H1
Бренд: Eplus Страницы: 17
Omega Engineering DP-F30 Series Operator'S Manual preview
DP-F30 Series
Бренд: Omega Engineering Страницы: 42
E+E Elektronik EE776 Series Manual preview
EE776 Series
Бренд: E+E Elektronik Страницы: 36
P&E Microcomputer Systems MON08 MULTILINK User Manual preview
MON08 MULTILINK
Бренд: P&E Microcomputer Systems Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды