NEC NEAX2400 ICS, Руководство по программированию

Страница: 597 / 1089

NEAX2400 IPX Feature Programming Manual
Page 554
NDA-24297, Issue 1
O-2 Outgoing Trunk Queuing
Programming
STEP 1: ASYD - System Data 1, Index 68, Bit 3. Enables automatic cancel timer, as set in System Data 1,
Index 159. 0/1: -/Enable.
System Data 1, Index 159. OGQ release timer. Standard data of 00H for 30 minutes may be assigned.
(RAM data of 3C [Hex] provides for 30 minutes).
System Data 2, Index 4, Bit 0. Should the access code for CALL BACK and OGQ be the same? 0/1:
No/Yes. Usually assign data “1”. Assign on a per-tenant basis.
System Data 2, Index 4, Bit 1. Enable Automatic OGQ? 0/1: No/Yes. Assign on a per-tenant basis.
Automatic operation eliminates the need to access via dial pad.
System Data 2, Index 4, Bit 2. Enable OFF-HOOK OGQ for the Attendant Console? 0/1: No/Yes.
Assign on a per-tenant basis. (See OUT GOING TRUNK QUEUING-ATTENDANT
[O-16] .)
System Data 1, Index 139, timer for the recall ringing.
STEP 2: ANPD - Reserve a number level for service feature access and cancel. Assign Connection Indexes, CI
= N, H, B; Normal (N), Hooking (H), and Busy (B) (applicable to any feature assigned to this level).
Assign NND in accordance with a predetermined numbering plan.
STEP 3: ASPA - If System Data 2, Index 4, Bit 0 is assigned for separate access codes, assign an access code to
OGQ, SRV = SSC (Service Code), SID = 19, and to OGQ cancel, SRV = SSC (Service Code), SID =
20. Assign SID = 19 for a Connection Index of Busy (B) and SID = 20 for a Connection Index of
Normal (N). If the access codes are the same, either the access codes for OGQ or the access codes for
CALL BACK may be assigned.
STEP 4: ASFC - If access codes are separate, assign a Service Feature Class that allows SFI 1 to stations that
will have OGQ. If access codes are the same, assign an SFC that allows SRI 1, SFI 1 and SFI 2 to the
station.
STEP 5: ARTD - Routes to be used for OGQ must be flagged in CDN 9:TQ, Trunk Queuing Service. Always
allow queuing to Route 31, the LCR (S) flag route.
STEP 6: AKYD
- D
term
- set the following data to assign CALL BACK Key. Type:Function:CALL BACK [5].
STEP 7: ADSL - SN=6 (Trunk is Busy) and FKY=5 (Call Back; CB).
This command is used for assigning the function to each soft key.
FCCS Programming
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
Note 1
STEP 1: ASYDN - These data must be assigned to the NCN.
System Data 1, Index 41: Designate the Trunk Queuing Override Timer
Index 68, b3: Enables automatic cancel timer
0/1: -/Automatic cancel timer is Available
Index 159: Designate Automatic Cancel Timer
STEP 2: ASPAN
- These data must be assigned to the NCN.
TN: Tenant Number
ACC: Access number
CI: B = Busy (for Entry), N = Normal (for Cancel)
SRV: SSC
SID: 19 = OG Queuing-Entry