NEC NEAX2400 ICS, Руководство по программированию

Страница: 76 / 1089

NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1
Page 33
Authorization Code A-20
Programming (cont’d)
STEP 2: ANPD - Reserve a number level for feature access. Assign for Normal (N), Hooking (H), and Busy
(B) (if applicable to any feature in this level). Assign NND in accordance with a predetermined
numbering plan.
STEP 3: ASPA
- For SRV = SSC (Service Code), SID = 42, assign the access code. For the NND parameter, no
assignment is required when AUTHORIZATION CODE operates by itself. When Account Code
operates with AUTHORIZATION CODE, assign for SRV = SSC (Service Code), SID = 42. The NND
value will include the number of digits in the AUTHORIZATION CODE access code, and Account
Code. For example:
45 – 26428 – 623423 – 9-1-617-555-2323
(ACC) (Auth Code) (Account Code) (Destination Code)
ASPA ACC=45 NND=8 (ACC + Account Code)
ASPA
- For SRV = LCR (Least Cost Route Selection) / LCRS (Register Sender LCR), if operating
Procedure 2 is to be used, (dialing the AUTHORIZATION CODE after the number dialed), then
assign data “1” to the AH parameter when programming the LCR(S) access code. Therefore, operating
Procedure 2 is only available with LEAST-COST ROUTING - 3/6 DIGIT [L-5].
STEP 4: ASFC
- For stations allowed AUTHORIZATION CODE, assign a Class of Service that allows SFI
27.
STEP 5: AMND
- For Tenant 0, assign the Destination Code (DC) as the first digit of all AUTHORIZATION
CODES and the Maximum Necessary Digits (MND) of the AUTHORIZATION CODE. For the above
example, a DC of 2 is assigned with an MND of 7. The MND value will include the digits added by the
Checksum method.
STEP 6: AATC
- Assign the TN, Digit Code (DC) (the actual code itself), the AUTHORIZATION CODE
RESTRICTION (ACR) as data “1” and Service Feature Class (SFC) and Route Restriction Class
(RSC). If ACR is assigned as data 2. Allowed: RSC and SFC parameters are not programmed. (SFC
parameters are not operational.)
STEP 7: LATC
- List up all the AUTHORIZATION CODES. This is the simplest way to determine what digits
have been added to the system with the Checksum method. This is not required if the Checksum
method is not used.
FCCS Programming
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
Note
STEP 1: ANPDL - Reserve a number level for feature access. Assign for Normal (N), Hooking (H), and Busy
(B) (if applicable to any feature in this level). Assign NND in accordance with a predetermined
numbering plan.
STEP 2: ASPAL
- For SRV = SSC (Service Code), SID = 42, assign the access code. For the NND parameter,
no assignment is required when AUTHORIZATION CODE operates by itself. When Account Code
operates with AUTHORIZATION CODE, assign for SRV = SSC (Service Code), SID = 42. The NND
value will include the number of digits in the AUTHORIZATION CODE access code, and Account
Code.
For SRV = LCR (Least Cost Route Selection) / LCRS (Register Sender LCR), if operating Procedure 2
is to be used, (dialing the AUTHORIZATION CODE after the number dialed), then assign data “1” to
the AH parameter when programming the LCR(S) access code. Therefore, operating Procedure 2 is
only available with LEAST-COST ROUTING - 3/6 DIGIT [L-5].