NEC NEAX2400 ICS, Руководство по программированию

Страница: 175 / 1089

NEAX2400 IPX Feature Programming Manual
Page 132
NDA-24297, Issue 1
C-5 Call Forwarding - All Calls
Interactions (cont’d)
7. When CALL FORWARDING-ALL CALLS is in effect, the activating station may be used to originate
calls. See System Data 2, Index 6, Bit 4.
8. When a station is call forwarded, the destination station is recorded for STATION MESSAGE DETAIL
RECORDING [S-10].
9. CALL FORWARDING-ALL CALLS can be overridden, allowing Station B to initiate or transfer calls
back to Station A.
10. STATION-TO-STATION CALLING [S-11] must first be provided.
Programming
STEP 1: ASYD
- System Data 1, Index 4, Bit 6. One burst of ringing at the forwarding station when CALL
FORWARDING-ALL CALLS is in service? 01: No/Yes.
System Data 1, Index 248, Bit 7. Dial tone to be sent out when a station on which CALL
FORWARDING-ALL CALLS is set, goes off-hook to place an outgoing call 0/1: Dial Tone/Special
Dial Tone.
System Data 1, Index 69, Bit 1 (Bit 2 - Call Forward Recall Tone). A burst of ringback tone to alert the
person receiving a call that this is a CALL FORWARDING-ALL CALLS call. In service? 0/1: No/
Yes. Normally assigned as data “0”.
System Data 2, Index 6, Bit 4. Enable station set for CALL FORWARDING-ALL CALLS be allowed
to use phones normally. If data “0” is assigned, the station will only be able to call the Attendant
Console. Assign on a per-tenant basis.
STEP 2: ANPD
- Reserve a number level for feature access and cancel. Assign Connection Index, (CI) = N, H,
B; Normal, Hooking, and Busy (applicable to any feature assigned to this level). Assign NND in
accordance with a predetermined numbering plan.
STEP 3: ASPA - Assign an access code to CALL FORWARDING-ALL CALLS entry SID = 8, and to CALL
FORWARDING-ALL CALLS cancel SID = 9. Assign CI for Normal (N) service.
STEP 4: ASFC - Assign a Service Feature Class that allows SFI = 7 to stations that will activate CALL
FORWARDING - ALL CALLS.
STEP 5: AKYD - For D
term
sets, CALL FORWARDING-ALL CALLS may be assigned to a programmable
line/feature key. Assign Type:Function:CALL FORWARDING-ALL CALLS [2].
STEP 6: ATNR - Allow tenant-to-tenant connection for Inter and Intra-tenant connections. Assign Tenant
Restriction Index (TRI) = 1. For this feature to be set by the Attendant Console, assign Inter an Intra-
Tenant connection TRI = 3, via the attendant Console. Also allow TRI = 0, station-to-station calling.
FCCS Programming
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
Note 1
STEP 1: ASYDL - This data must be assigned to the node set Call Forwarding service.
System Data 1, Index 640: Assign the FPC of the node providing the attendant console.
Note 1: When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required
in addition to ASYDL or ASYDN.
Note 2:
The data of the ASFC command is assigned to the node set Call Forwarding service.