NEC NEAX2400 ICS, Руководство по программированию

Страница: 171 / 1089

NEAX2400 IPX Feature Programming Manual
Page 128
NDA-24297, Issue 1
C-3D Call Forwarding - Don’t Answer - D
term
Interactions (cont’d)
4. CALL FORWARDING-DON’T ANSWER-D
term
to an Attendant Console will not operate when the
system is in Night mode. If ATTENDANT NIGHT TRANSFER [A-19] is provided, the call is forwarded
to the ATTENDANT NIGHT TRANSFER [A-19] station.
5. If the CALL FORWARDING-DON’T ANSWER-D
term
target station is a D
term
and DO NOT DISTURB
[D-21D] has been set, Call Forwarding is not activated. The station will ring, and the timer setting in
System Data 1, Index 145 is ignored.
6. When CALL FORWARDING-DON’T ANSWER-D
term
is set from Station A to Station B, Station A is
idle, Station B is busy, and Station A will ring. The timer setting in System Data 1, Index 145 is ignored.
7. When a call is call forwarded, the destination station is recorded for STATION MESSAGE DETAIL
RECORDING [S-10].
8. STATION-TO-STATION CALLING [S-11] must first be provided.
Programming
STEP 1: ASYD
- System Data 1, Index 5, Bit 0. Access codes for CALL FORWARDING-BUSY LINE [C-2]
and CALL FORWARDING - DON’T ANSWER- D
term
are same or separate? 0/1: Same/Separate.
System Data 1, Index 69, Bits 1 and 2 use a short tone to alert the person receiving the call that this is a
CALL FORWARDING-DON’T ANSWER-D
term
call? 0/1: No/Yes.
System Data 1, Index 139. Assign the No Answer timer for station-to-station, DID and TIE Line calls.
For 30 seconds, assign 00H, (RAM data is 3FH).
System Data 1, Index 141. Assign the No Answer time for incoming calls via the Attendant Console. It
will then be forwarded to the next station according to System Data 1, Index 145 timer. For 10
seconds, assign 00H. (RAM data is 3FH).
System Data 1, Index 145. Assign the time an incoming call via the Attendant Console will ring at the
CALL FORWARD-DON’T ANSWER-D
term
station before recalling to the Attendant Console. For 30
seconds, assign 00H. [RAM data is 9FH.] Index 145 must be longer than Index 141.
System Data 2, Index 6, Bit 0. Enable CALL FORWARDING-DON’T ANSWER-D
term
on a per-
tenant basis.
System Data 2, Index 6, Bit 7. Enable CALL FORWARDING-DON’T ANSWER-D
term
via the
Attendant Console.
STEP 2: ANPD
- Reserve a number level for service feature access and cancel. Assign for Normal (N),
Hooking (H) and Busy (B). Assign NND in accordance with a predetermined numbering plan.
STEP 3: ASPA - Assign an access code to CALL FORWARDING - DON’T ANSWER - D
term
for entry, SID=
12, and to CALL FORWARDING - DON’T ANSWER - D
term
for cancel, SID = 13. Assign
Connection Status Index (CI) for Normal (N) service.
STEP 4: ASFC
- Assign the stations a Service Feature Class that allows SFI = 8 to allow CALL
FORWARDING-DON’T ANSWER-D
term
.
STEP 5: ADSL - Assign SN=1 (Originating; DT Connection) and FKY=22 (Call Forwarding Don’t Answer;
FDN).
This command is used for assigning the function to each soft key.
STEP 6: AKYD - For D
term
sets, CALL FORWARDING - DON’T ANSWER -D
term
may be assigned to a
programmable line/feature key. Assign Type:Function:CALL FORWARD-DON’T ANSWER [22].
STEP 7: ATNR - Allow tenant-to-tenant connection for Inter and Intra-tenant connections. Assign Tenant
Restriction Index (TRI) = 1. For this service feature to be set by the Attendant Console, assign TRI = 3
for Inter and Intra-Tenant connection via the Attendant Console. Also assign TRI = 0, station-to-
station calling.