manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

Matrix SPARSH VP710 User Guide

71

•

Enter the desired value in the 

IP Address, IPv6 IP Prefix, Gateway, Primary DNS

 and 

Secondary DNS

 

field respectively.

•

Tap 

 to accept the change or 

 

to cancel.

If you are using an xDSL modem for IPv4 network connection, you can connect your phone to the Internet 
via PPPoE mode. Set the WAN port as a PPPoE port. The PPPoE port will perform a PPP negotiation to 
obtain the IP address. Contact your service provider for the PPPoE username and password.

PPPoE

PPPoE (Point-to-Point Protocol over Ethernet) is a network protocol used by Internet Service Providers (ISPs) to 
provide Digital Subscriber Line (DSL) high speed Internet services. PPPoE allows an office or building-full of users 
to share a common DSL connection to the Internet. PPPoE connection is supported by the IP phone Internet port. 
Contact your ISP for the PPPoE user name and password.

Procedure

PPPoE can be configured using the configuration files or locally.

Configuration File

<MAC>.cfg

Configure PPPoE on the IP phone.

Configure the user name and password 
for PPPoE on the IP phone.

For more information, refer 

“Appendix 

D - Configuration Parameters”

.

 

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Panasonic KX-TGW420 Quick Manual preview
KX-TGW420
Brand: Panasonic Pages: 4
Pantech PS-300 User Manual preview
PS-300
Brand: Pantech Pages: 75
Telesis ITS821 Installation And User Manual preview
ITS821
Brand: Telesis Pages: 11
OEM SC7701 User Manual preview
SC7701
Brand: OEM Pages: 25
Aastra SIP SIP9133i User Manual preview
SIP SIP9133i
Brand: Aastra Pages: 22
Alcatel IDOL 3 6045F Manual preview
IDOL 3 6045F
Brand: Alcatel Pages: 73
Grandstream Networks GXP 2020 Quick Installation Manual preview
GXP 2020
Brand: Grandstream Networks Pages: 1
Pantech Verizon TXT8035PP User Manual preview
Verizon TXT8035PP
Brand: Pantech Pages: 50
Spice C-5300 Manual preview
C-5300
Brand: Spice Pages: 21
XONTEL XT-07P User Manual preview
XT-07P
Brand: XONTEL Pages: 13
Zte Z6530V User Manual preview
Z6530V
Brand: Zte Pages: 23
Samsung A740 - SPH Cell Phone User Manual preview
A740 - SPH Cell Phone
Brand: Samsung Pages: 94
Samsung A847M User Manual preview
A847M
Brand: Samsung Pages: 140
Samsung A847 User Manual preview
A847
Brand: Samsung Pages: 142
Samsung A767 - SGH Propel Cell Phone 45 MB User Manual preview
A767 - SGH Propel Cell Phone 45 MB
Brand: Samsung Pages: 164
Samsung A837 User Manual preview
A837
Brand: Samsung Pages: 187
Samsung A850 - SCH Cell Phone User Manual preview
A850 - SCH Cell Phone
Brand: Samsung Pages: 249
Samsung A840 - SPH Cell Phone Owner'S Manual preview
A840 - SPH Cell Phone
Brand: Samsung Pages: 273

Brands by name

Popular brands

Load more brands