manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

Matrix SPARSH VP710 User Guide

563

Procedure

LLDP can be configured using the configuration files or locally.

TIA Organizationally 

Specific TLVs

Media Capabilities

The MED device type of the IP phone and the 
supported LLDP-MED TLV type can be encapsulated in 
LLDPDU.

The supported LLDP-MED TLV types are: LLDP-MED 
Capabilities, Network Policy, Extended Power via 
MDI-PD and Inventory.

Network Policy

Port VLAN ID, application type, L2 priority and DSCP 
value.

Extended Power-via-MDI

Power type, source, priority and value.

Inventory – Hardware 
Revision

Hardware revision of the IP phone.

Inventory – Firmware 
Revision

Firmware revision of the IP phone.

Inventory – Software 
Revision

Software revision of the IP phone.

Inventory – Serial Number

Serial number of the IP phone.

Inventory – Manufacturer 
Name

Manufacturer name of the IP phone.

Inventory – Model Name

Model name of the IP phone.

Asset ID

Assertion identifier of the IP phone.

The default value is “asset”.

Configuration File

<MAC>.cfg

Configure LLDP feature.

For more information, refer 

“Appendix D - Configuration 
Parameters”

.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Iget ARROW Quick Start Manual preview
ARROW
Brand: Iget Pages: 54
M2M Easy 2 Installation Manual preview
Easy 2
Brand: M2M Pages: 88
HTC Desire 626S Quick Start Manual preview
Desire 626S
Brand: HTC Pages: 2
Hisense HLTE100E User Manual preview
HLTE100E
Brand: Hisense Pages: 41
Alcatel 2057 Series User Manual preview
2057 Series
Brand: Alcatel Pages: 27
PSC Falcon 510 User Manual preview
Falcon 510
Brand: PSC Pages: 32
Vox Yealink SIP-T27 User Manual preview
Yealink SIP-T27
Brand: Vox Pages: 12
Proolin VoIP Tech CS-830 User Manual preview
CS-830
Brand: Proolin VoIP Tech Pages: 25
PCD c5017 User Manual preview
c5017
Brand: PCD Pages: 62
ICON IP2032 Quick Reference Manual preview
IP2032
Brand: ICON Pages: 8
ORA VERA F2401 User Manual preview
VERA F2401
Brand: ORA Pages: 26
Asus AIGURUSV1 - Eee Videophone AiGuru SV1 Wireless IP Video Phone User Manual preview
AIGURUSV1 - Eee Videophone AiGuru SV1 Wireless IP Video Phone
Brand: Asus Pages: 32
Zte Orange Zali User Manual preview
Orange Zali
Brand: Zte Pages: 184
Zte Z917VL User Manual preview
Z917VL
Brand: Zte Pages: 140
Panasonic KX-PRD260 Quick Manual preview
KX-PRD260
Brand: Panasonic Pages: 10
Panasonic KX-PRL262 Operating Instructions Manual preview
KX-PRL262
Brand: Panasonic Pages: 17
Myria MY9081BK User Manual preview
MY9081BK
Brand: Myria Pages: 58
Toshiba Strata CIX DKT2404-DECT User Manual preview
Strata CIX DKT2404-DECT
Brand: Toshiba Pages: 62

Brands by name

Popular brands

Load more brands