Matrix SPARSH VP710 User Manual Download Page 819

Page: 819 / 1046

Matrix SPARSH VP710 User Guide

811

Play Local DTMF Tone

Incoming Intercom calls

Example

features.dtmf.replace_tran = 0

Parameter

features.dtmf.transfer

Configuration File

<MAC>.cfg

Description

Configures the DTMF digits to be transmitted to
perform call transfer.

Valid values are: 0-9, *, # and A-D.

Note:

It works only if the value of the parameter

“features.dtmf.replace_tran” is set to 1 (Enabled).

Default Value

Blank

Range

String within 32 characters

Example

features.dtmf.transfer = 123

Parameter

features.play_local_dtmf_tone_enable

Configuration File

<MAC>.cfg

Description

Enables or disables the IP phone to play a local DTMF
tone.

If it is set to 1 (Enabled), you can hear the DTMF tone
when pressing the IP phone’s keypad during a call.

Default Value

Range

0 or 1

0-Disabled

1-Enabled

Example

features.play_local_dtmf_tone_enable = 1

Parameter

features.intercom.allow

Configuration File

<MAC>.cfg

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands