Matrix SPARSH VP710 User Manual Download Page 877

Page: 877 / 1046

Matrix SPARSH VP710 User Guide

869

Multicast Paging Key

Default Value

Range

0-Disabled

1-Enabled

Example

static.network.ipv6_icmp_v6.enable = 1

Parameter

linekey.X.type

Configuration File

<MAC>.cfg

Description

Configures a DSS key as a multicast paging key on the IP
phone.

The digit 24 stands for the key type Multicast Paging.

For line keys:

X ranges from 1 to 27.

Default:

The default value of the line key 1-16 is 15, and the default
value of the line key 17-27 is 0.

Range

24 (Refer the above content)

Example

linekey.2.type = 24

Parameter

linekey.X.value

Configuration File

<MAC>.cfg

Description

Configures the multicast IP address and port number.

For line keys:

X ranges from 1 to 27.

Note:

The valid multicast IP addresses range from

224.0.0.0 to 239.255.255.255.

Range

String within 99 characters

Value

Blank

Example

linekey.2.value = 224.5.5.6:10008

Parameter

linekey.X.label

Configuration File

<MAC>.cfg

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands