Matrix SPARSH VP710 User Manual Download Page 829

Page: 829 / 1046

Matrix SPARSH VP710 User Guide

821

Parameter

voice.tone.info

Configuration File

<MAC>.cfg

Description

Customizes the info tone. The phone will play the info

tone with the special information, for example, the
number you are calling is not in service.

The value format is Freq/Duration. For more

information on the value format, refer to the
parameter “voice.tone.dial”.

Note:

It works only if the value of the parameter

“voice.tone.country” is set to Custom.

Default Value

Blank

Range

String

Example

Parameter

voice.tone.stutter

Configuration File

<MAC>.cfg

Description

Customizes the tone when the IP phone receives a

voice mail.

The value format is Freq/Duration. For more

information on the value format, refer to the

parameter “voice.tone.dial”.

Note:

It works only if the value of the parameter

“voice.tone.country” is set to Custom.

Default Value

Blank

Range

String

Example

Parameter

voice.tone.autoanswer

Configuration File

<MAC>.cfg

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands