manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

46

Matrix SPARSH VP710 User Guide

Viewing the Phone Status

You can view phone status via phone user interface or web user interface.

Available information of phone status includes:

•

General information (IP address, MAC address and firmware version)

•

Network status (IPv4 status or IPv6 status, IP mode and MAC address)

•

IPv4 uses a 32-bit address.

•

IPv6 is an updated version of the current Internet Protocol to meet the increased demands for unique 
IP addresses, using a 128-bit address.

•

Phone status (product name, hardware version, firmware version, product ID, MAC address, device 

certificate status and Android version)

•

Account status (register status of SIP accounts)

•

Storage information (internal storage, internal SD and USB storage

The storage information is sorted and displayed with different categories. The following table lists usage of each 
category

You can view the device certificate status and storage information via phone user interface only.

Category 

Usage 

Apps 

Display the memory cost of the application data and media content. 

Cached data 

Tap to clear cached data for all apps. 

Pictures, 

videos 

Tap to view the pictures/videos by 

Gallery 

application. 

Audio 

Tap to open the file system of the storage. You can browse the file system to view all audios 
in the internal SD card or USB flash drive. 

Downloads 

Display the memory cost of the downloaded files. 

Misc. 

Tap to display all folders on the IP phone. You can then select the folders to be cleaned up. 

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Panasonic G600 Technical Manual preview
G600
Brand: Panasonic Pages: 45
QJO Q55 User Manual preview
Q55
Brand: QJO Pages: 32
Yealink SIP-T38G Reference Manual preview
SIP-T38G
Brand: Yealink Pages: 2
Yealink SIP-T32G Quick Installation Manual preview
SIP-T32G
Brand: Yealink Pages: 2
Yealink SIP-T29G Quick Reference User Manual preview
SIP-T29G
Brand: Yealink Pages: 2
Yealink SIP-T23G Quick Reference User Manual preview
SIP-T23G
Brand: Yealink Pages: 2
Yealink Yealink SIP-T28P Setup Manual preview
Yealink SIP-T28P
Brand: Yealink Pages: 10
Yealink Yealink SIP-T28P Quick Install preview
Yealink SIP-T28P
Brand: Yealink Pages: 2
Yealink SIP-T21 E2 Quick Installation Manual preview
SIP-T21 E2
Brand: Yealink Pages: 4
Yealink Yealink SIP-T28P Quick User Manual preview
Yealink SIP-T28P
Brand: Yealink Pages: 2
Yealink Yealink SIP-T28P Quick Reference Manual preview
Yealink SIP-T28P
Brand: Yealink Pages: 4
Yealink SIP-T2XP Auto Provisioning Manual preview
SIP-T2XP
Brand: Yealink Pages: 158
Yealink One Talk W78B Quick Start Manual preview
One Talk W78B
Brand: Yealink Pages: 6
Yealink T41P Skype Quick User Manual preview
T41P Skype
Brand: Yealink Pages: 4
Yealink MP54 Quick Installation Manual preview
MP54
Brand: Yealink Pages: 16
Yealink MP58 User Manual preview
MP58
Brand: Yealink Pages: 73
Yealink SIP VP-T49G Developer'S Manual preview
SIP VP-T49G
Brand: Yealink Pages: 120
Yealink SIP-T38G Quick Reference preview
SIP-T38G
Brand: Yealink Pages: 2

Brands by name

Popular brands

Load more brands