manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

Matrix SPARSH VP710 User Guide

947

Example

account.1.codec.g722_1c_48kpbs.enable = 1

account.1.codec.g722_1c_32kpbs.enable = 1

account.1.codec.g722_1c_24kpbs.enable = 1

account.1.codec.g722_1_24kpbs.enable = 1

account.1.codec.g722.enable = 1

account.1.codec.pcmu.enable = 1

account.1.codec.pcma.enable = 1

account.1.codec.g729.enable = 1

account.1.codec.opus.enable = 0

account.1.codec.g726_40.enable = 0

account.1.codec.g726_32.enable = 0

account.1.codec.g726_24.enable = 0

account.1.codec.g726_16.enable = 0

account.1.codec.ilbc.enable = 0

account.1.codec.g723_63.enable = 0

account.1.codec.g723_53.enable = 0

It means that the codecs G.722.1c(48kb/s), 
G.722.1c(32kb/s), G.722.1c(24kb/s), G.722.1(24kb/s), 
G722, PCMU, PCMA and G729 are enabled on the 
account 1.

Note: 

The name of audio codec in this parameter 

should be the correct one as listed in the above 
example, otherwise the corresponding configuration 
will not take effect.

Parameter

-

account.X.codec.<payload_type>.pri
ority

(where <payload_type> should be 
replaced by the name of audio 
codec)

Configuration File

<MAC>.cfg

Description

Configures the priority of the enabled audio codec for 
account X.

X ranges from 1 to 16

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Samsung SPH-a660 Series Reference Manual preview
SPH-a660 Series
Brand: Samsung Pages: 2
Samsung SGH-S100 User Manual preview
SGH-S100
Brand: Samsung Pages: 73
Samsung SGH-E715 User Manual preview
SGH-E715
Brand: Samsung Pages: 164
Samsung SCH-a600 Series Quick Reference Card preview
SCH-a600 Series
Brand: Samsung Pages: 2
H3C Aolynk EP302 User Manual preview
Aolynk EP302
Brand: H3C Pages: 68
RADVision Scopia XT5000 Series Installation Manual preview
Scopia XT5000 Series
Brand: RADVision Pages: 184
Samsung Memoir SGH t929 Manual Del Usuario preview
Memoir SGH t929
Brand: Samsung Pages: 196
Samsung SM-G920W8 Quick Start Manual preview
SM-G920W8
Brand: Samsung Pages: 23
Samsung SGH-D780 Quick Start Manual preview
SGH-D780
Brand: Samsung Pages: 7
Samsung SCH-X609 Quick Reference Card preview
SCH-X609
Brand: Samsung Pages: 2
Samsung GALAXY F15 5G User Manual preview
GALAXY F15 5G
Brand: Samsung Pages: 135
Handspring Treo 300 Brochure preview
Treo 300
Brand: Handspring Pages: 2
Ulefone GQ3039 User Manual preview
GQ3039
Brand: Ulefone Pages: 32
Yealink SIP-T21 User Manual preview
SIP-T21
Brand: Yealink Pages: 143
Slican VPS-804P Instruction Manual preview
VPS-804P
Brand: Slican Pages: 50
Sagem MY400L User Manual preview
MY400L
Brand: Sagem Pages: 94
OUKITEL WP13 Quick Start Manual preview
WP13
Brand: OUKITEL Pages: 62
WayteQ TALK 5H User Manual preview
TALK 5H
Brand: WayteQ Pages: 24

Brands by name

Popular brands

Load more brands