Matrix SPARSH VP710 User Manual Download Page 817

Page: 817 / 1046

Matrix SPARSH VP710 User Guide

809

Suppress DTMF Display

Parameter

features.dtmf.duration

Configuration File

<MAC>.cfg

Description

Configures the duration time (in milliseconds) for
DTMF.

Note:

If the time interval to between two DTMF digits

is less than this value, two or more

same DTMF digits could be identified as one DTMF
digit. This may cause the loss of one or

more DTMF digits. For example, 2662 may be
identified as 262. If so, you can modify the

value of this parameter to a little lower than the
default value.

Default Value

100

Range

0 to 300

Example

features.dtmf.repetition = 100

Parameter

features.dtmf.volume

Configuration File

<MAC>.cfg

Description

Configures the frequency level of DTMF digits (in db).

Default Value

-10

Range

-33 to 0

Example

features.dtmf.volume= -10

Parameter

features.dtmf.hide

Configuration File

<MAC>.cfg

Description

Enables or disables the IP phone to suppress the
display of DTMF digits during an active

call.

If it is set to 1 (Enabled), the DTMF digits are
displayed as asterisks.

Default Value

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands