Matrix SPARSH VP710 User Manual Download Page 906

Page: 906 / 1046

898

Matrix SPARSH VP710 User Guide

CDP

VPN (Virtual Private network)

Parameter

static.network.cdp.enable

Configuration File

<MAC>.cfg

Description

Enables or disables the CDP (Cisco Discovery Protocol)
feature on the IP phone.

If it is set to 1 (Enabled), the IP phone will attempt to
determine its VLAN ID through CDP.

Note:

If you change this parameter, the IP phone will

reboot to make the change take effect.

Range

0-Disabled

1-Enabled

Default

Example

static.network.cdp.enable = 0

Parameter

static.network.cdp.packet_interval

Configuration File

<MAC>.cfg

Description

Configures the interval (in seconds) for the IP phone to
send the CDP (Cisco Discovery Protocol) request.

Note:

It works only if the value of the parameter

“static.network.cdp.enable” is set to 1 (Enabled). If you
change this parameter, the IP phone will reboot to make
the change take effect.

Range

Integer from 1 to 3600

Default

Example

static.network.cdp.packet_interval = 60

Parameter

static.network.vpn_enable

Configuration File

<MAC>.cfg

Description

Enables or disables OpenVPN feature on the IP phone.

Note:

If you change this parameter, the IP phone will

reboot to make the change take effect.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Matrix SPARSH VP710, User Manual, Page: 906 / 1046

Search results

Summary of Contents for SPARSH VP710

Reviews: