manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

Matrix SPARSH VP710 User Guide

579

•

Your can do the following:

•

Tap the 

Hold

 soft key to place the current multicast RTP session on hold.

The sender¡¦s phone places the multicast RTP session on hold and receiver¡¦s phone releases the 
session.
To resume the held multicast RTP session, tap the 

Resume

 soft key.

The multicast RTP session is established again.

•

Tap the 

EndCall

 soft key to cancel the multicast RTP session.

•

Tap the 

Record

 soft key to record a call.

To stop recording, tap the 

Stop

 soft key

•

Multicast RTP is only one way from the sender to the multicast address(es) (receiver).

•

 For outgoing RTP multicasts, all other existing calls on the phone will be placed on hold.

To send RTP stream via a paging key list when the receiver’s phone is idle:

•

Tap paging list key when the phone is idle.

•

Do one of the following to send RTP:

•

Tap the desired paging group.

•

Tap 

 

after the desired paging group, and then tap 

Multicast

 

Paging

.

•

Your can do the following:

•

Tap the 

Hold

 soft key to place the current multicast RTP session on hold.

The sender¡¦s phone places the multicast RTP session on hold and receiver¡¦s phone releases the 
session.
To resume the held multicast RTP session, tap the Resume soft key.
The multicast RTP session is established again.

•

Tap the 

EndCall

 soft key to cancel the multicast RTP session.

•

Tap the 

Record

 soft key to record a call.

To stop recording, tap the 

Stop

 soft key

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Federal Signal Corporation I-IPTEL1 Manual preview
I-IPTEL1
Brand: Federal Signal Corporation Pages: 20
TCL 10SE Manual preview
10SE
Brand: TCL Pages: 52
Talkswitch TS-850i User Manual preview
TS-850i
Brand: Talkswitch Pages: 17
Vingtor AACM-144-V10 Installation/Configuration Manual preview
AACM-144-V10
Brand: Vingtor Pages: 76
Mitsubishi Trium T300 User Manual preview
Trium T300
Brand: Mitsubishi Pages: 72
Kyocera Qua Phone Settings Manual preview
Qua Phone
Brand: Kyocera Pages: 2
Manta TEL1713 Manual Manual preview
TEL1713
Brand: Manta Pages: 20
HANNspree HANNSzephyr User Manual preview
HANNSzephyr
Brand: HANNspree Pages: 75
Majestic LUCKY 59 FLIP Manual preview
LUCKY 59 FLIP
Brand: Majestic Pages: 57
Manta TEL1707 User Manual preview
TEL1707
Brand: Manta Pages: 28
Grandstream Networks GXP1520 Quick Installation Manual preview
GXP1520
Brand: Grandstream Networks Pages: 29
Gigaset PREMIUM 300 Manual preview
PREMIUM 300
Brand: Gigaset Pages: 88
Lephone w2 User Manual preview
w2
Brand: Lephone Pages: 23
Teldat elmeg IP130 User Manual preview
elmeg IP130
Brand: Teldat Pages: 165
ADTRAN Aastra 9133i IP User Manual preview
Aastra 9133i IP
Brand: ADTRAN Pages: 31
Blu Grand M3 User Manual preview
Grand M3
Brand: Blu Pages: 36
SoftBank 706SC User Manual preview
706SC
Brand: SoftBank Pages: 386
i-onik i422 Quick Start Manual preview
i422
Brand: i-onik Pages: 49

Brands by name

Popular brands

Load more brands