Matrix SPARSH VP710 User Manual Download Page 615

Page: 615 / 1046

Matrix SPARSH VP710 User Guide

607

Procedure

CLIP can be configured using the configuration files or locally.

Configuration File

<MAC>.cfg

Configure the registration line type.

Configure the call pull feature access

code.

Configure the private hold soft key.

Assign a private hold key.

For more information, refer

“Appendix D - Configuration
Parameters”

Local

Web User Interface

Configure the registration line type.

Configure the call pull feature access

code.

Navigate to:

http://<phoneIPAddress>/servlet?m=

mod_data&p=account-adv&q=load&

acc=0

Configure the private hold soft key.

Navigate to:

http://<phoneIPAddress>/servlet?m=

mod_data&p=settings-softkey&q=loa

Assign a private hold key.

Navigate to:

http://<phoneIPAddress>/servlet?m=

mod_data&p=dsskey&q=load

Phone User Interface

Assign a private hold key.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands