manualshive.com logo in svg

Matrix SPARSH VP710, User Manual, Page: 766 / 1046

Share
Download
Matrix SPARSH VP710 User Manual Download Page 766

758

Matrix SPARSH VP710 User Guide

Range

Valid values are:

0

-

Disabled

1

-

Enabled

If it is set to 0 (Off), the IP phone will use the IPv4 DNS 
obtained from DHCP.
If it is set to 1 (On), the IP phone will use manually 
configured static IPv4 DNS.
Note: It works only if the value of the parameter 
“static.network.internet_port.type” is set to
0 (DHCP). If you change this parameter, the IP phone 
will reboot to make the change take
effect.

Example

static.network.static_dns_enable = 0

Parameter

-

static.network.primary_dns

Configuration File

<MAC>.cfg

Description

Configures the primary IPv4 DNS server.

Note

: It works only if the value of the parameter 

"static.network.static_dns_enable" is set to 1(On). 

If you change this parameter, the IP phone will reboot 
to make the change take effect.

Default Value

Blank

Range

  

IPv4 Address

Example

static.network.primary_dns = 202.101.103.55

Parameter

-

static.network.secondary_dns

Configuration File

<MAC>.cfg

Description

Configures the secondary IPv4 DNS server.

Note

: It works only if the value of the parameter 

"static.network.static_dns_enable" is set to 1(On). 

If you change this parameter, the IP phone will reboot 
to make the change take effect.

Default Value

Blank

Range

  

IPv4 Address

Example

static.network.secondary_dns = 202.101.103.54

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments