Matrix SPARSH VP710 User Manual Download Page 156

Page: 156 / 1046

148

Matrix SPARSH VP710 User Guide

To adjust the talking volume during a call:

•

Press

to adjust the volume of currently engaged audio device (handset,speakerphone or

headset).

•

You can also drag the volume slider to adjust the talking volume.

To adjust the key tone volume when the phone is on the dialing screen:

•

Press

to adjust the key tone volume.

You can also drag the volume slider to adjust the key tone volume.

To adjust the media volume:

You can adjust the media volume in multiple scenarios. The following takes playing the audios by FileManager
application as example:

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands