Matrix SPARSH VP710 User Manual Download Page 935

Page: 935 / 1046

Matrix SPARSH VP710 User Guide

927

Replace Rule

Parameter

dialplan.replace.prefix.X

(X ranges from 1 to 100)

Configuration File

<MAC>.cfg

Description

Configures the entered number to be replaced.

Default Value

Blank

Range

String within 32 characters

Example

dialplan.replace.prefix.1 = 1

Note: It works only if the values of the parameters
“dialplan.digitmap.enable” and

“account.X.dialplan.digitmap.enable” are set to 0
(Disabled).

Parameter

dialplan.replace.replace.X

(X ranges from 1 to 100)

Configuration File

<MAC>.cfg

Description

Configures the alternate number to replace the
entered number.

Default Value

Blank

Range

String within 32 characters

Example

dialplan.replace.prefix.1 =1 and
dialplan.replace.replace.1 = 254245

When you enter the number ”1” and press the send
key, the number “254245” will replace the entered
number “1”.

Note:

It works only if the values of the parameters

“dialplan.digitmap.enable” and
“account.X.dialplan.digitmap.enable” are set to 0
(Disabled).

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands