Matrix SPARSH VP710 User Manual Download Page 85

Page: 85 / 1046

Matrix SPARSH VP710 User Guide

•

Tap

and then tap

WPS

The touch screen prompts “Press the Wi-Fi Protected Setup button on your router. It may be called “WPS”
or contain this symbol:”.

•

Long press the

WPS

key on your gateway/router.

Once WPS setup has completed successfully, the touch screen will prompt “Connected”.

Personal Identification Number (PIN)

To connect to the wireless network using PIN method via phone user interface:

•

Swipe down from the top of the screen or swipe left/right to go to the second idle screen.

•

Tap

Settings->Basic->Wi-Fi.

•

Tap the

radio box in the Wi-Fi field.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands