manualshive.com logo in svg

Matrix SPARSH VP710, User Manual, Page: 726 / 1046

Share
Download
Matrix SPARSH VP710 User Manual Download Page 726

718

Matrix SPARSH VP710 User Guide

•

Click 

Browse

.

•

Select firmware from the local system.

•

Click 

Upload

.

A dialog box pops up to prompt “Firmware of the SIP Phone will be updated. It will take 5 minutes to 
complete. Please don't power off!”

•

Click 

OK

 to confirm the upgrade.

Do not close and refresh the browser when the IP phone is upgrading the firmware via web user interface.

Upgrade Firmware from the Provisioning Server

IP phones support using FTP, TFTP, HTTP and HTTPS protocols to download configuration files and firmware from 
the provisioning server, and then upgrade firmware automatically.

IP phones can download firmware stored on the provisioning server in one of two ways:

•

Check for configuration files and then download firmware during start-up.

•

Automatically check for configuration files and then download firmware at a fixed interval or specific time.

Method of checking for configuration files is configurable.

Procedure

Configuration changes can be performed using the configuration files or locally.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments