Matrix SPARSH VP710 User Manual Download Page 684

Page: 684 / 1046

676

Matrix SPARSH VP710 User Guide

To configure the codecs to use and adjust the priority of the enabled codecs via web user interface:

•

Click on

Account ->Codec

•

Select the desired account from the

Account

list.

•

Select the desired codec from the

Disable Codecs

column and then click

The selected codec appears in the

Enable Codecs

column.

Configuration File

<MAC>.cfg

Configure the codecs to use on a

per-line basis.

Configure the priority and rtpmap

for the enabled codec.

For more information, refer

“Appendix D - Configuration
Parameters”

Local

Web User Interface

Configure the codecs to use on a

per-line basis.

Configure the priority and rtpmap

for the enabled codec.

Navigate to:

http://<phoneIPAddress>/servlet?p

=account-codec&q=load&acc=0

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands