manualshive.com logo in svg

Matrix SPARSH VP710, User Manual, Page: 212 / 1046

Share
Download
Matrix SPARSH VP710 User Manual Download Page 212

204

Matrix SPARSH VP710 User Guide

•

Tap 

OK

 to accept the change or 

Cancel

 to cancel.

Line Key Features

Line key features are explained below:

•

Line

•

Speed Dial

•

Voice  Mail

•

Direct Pickup

•

Group Pickup

•

DTMF

•

Prefix

•

Local Group

•

XML Group

•

LDAP

•

Conference

•

Forward

•

Transfer

•

Hold

•

DND

•

Group Listening

•

Zero Touch

•

URL

•

Phone Lock

•

Directory

•

Mobile Account

Line

You can use this key feature to accept incoming calls, place active calls on hold or resume a held call.

Dependencies: 

Type (Line)

Account ID 

(the account this feature will be applied to)

Label 

(key label displayed on the touch screen)

Usage: 

When the phone receives an incoming call,

•

Tap the line key to accept the incoming call.

•

Tap the line key to place a new call and the active call is placed on hold.

•

Tap the line key again to resume the held call.

Speed Dial

You can use this key feature to speed up dialing the numbers frequently used/hard to remember or perform blind 
transfer conveniently during the call.

Dependencies: 

Type (Speed Dial)

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments