Matrix SPARSH VP710 User Manual Download Page 94

Page: 94 / 1046

Matrix SPARSH VP710 User Guide

To configure the PC port mode via web user interface:

•

Click on

Network->PC Port

•

Select the desired value from the

PC Port Active

list.

•

Click

Confirm

to save the change.

A dialog box pops up to prompt that settings will take effect after a reboot.

•

Click

to reboot the IP phone.

To disable the PC port via web user interface:

•

Click on

Network->PC Port

•

Select

Disabled

from the

PC Port Active

list.

•

Click

Confirm

to save the change.

A dialog box pops up to prompt that settings will take effect after a reboot.

•

Click

to reboot the IP phone.

Configuration File

<MAC>.cfg

Configure the PC port mode.

For more information, refer

“Appendix

D - Configuration Parameters”

Local

Web User Interface

Configure the PC port mode.

Navigate to

http://<phoneIPAddress>/servlet?m=m

od_data&p=network-pcport&q=load

Phone User Interface

None

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands