Matrix SPARSH VP710 User Manual Download Page 576

Page: 576 / 1046

568

Matrix SPARSH VP710 User Guide

You can specify a multicast codec for the IP phone to use for multicast RTP using the Configuration File.

Multicast Paging Key

For more information on how to configure the DSS Key, refer to Appendix D: Configuring DSS Key.

Paging List key

For more information on how to configure the DSS Key, refer to Appendix D: Configuring DSS Key.

Local

Web User Interface

Specify a multicast codec for the IP
phone to send the RTP stream.

Navigate to:

http://<phoneIPAddress>/
servlet?m=mod_data&p=features-
general&q=load

Configure the multicast IP address and
port number for a paging list key.

Configure the multicast paging group
name for a paging list key.

Configure the channel of the multicast

paging group for a paging list key.

Navigate to:

http://<phoneIPAddress>/
servlet?m=mod_

data&p=contacts-multicastIP&q=load

Assign a multicast paging key or a
paging list key.

Navigate to:

http://<phoneIPAddress>/
servlet?m=mod_data&p=dsskey&q=loa
d

Phone User Interface

Configure the multicast IP address and
port number for a paging list key.

Configure the channel of the multicast

paging group for a paging list key.

Configure the multicast paging group
name for a paging list key.

Assign a multicast paging key or a
paging list key.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands