manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

578

Matrix SPARSH VP710 User Guide

•

Select the desired channel from the 

Channel

 list.

Click 

Confirm

 to save the change.

•

The priorities of listening addresses are predefined: 1 with the highest priority, 31 with the lowest.

•

The phone plays a warning tone when receiving incoming multicast paging calls.

•

The phone will not receive a new incoming multicast paging call when there are two calls on the phone.

•

Multicast listening addresses is configurable via web user interface only.

Using Multicast Paging

To send RTP stream via a multicast paging key when the receiver’s phone is idle:

•

Tap the multicast paging key when the phone is idle.

The phone sends RTP to a preconfigured multicast address (IP: Port).Both the sender’s and receiver’s 
phones play a warning tone and the receiver automatically answers the multicast RTP session in the 

hands-free (speakerphone) mode.The multicast paging key icon will become 

 

and solid.

The following figure shows a multicast RTP session on the IP phone:

 

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Samsung Galaxy S Blaze 4G Instructions preview
Galaxy S Blaze 4G
Brand: Samsung Pages: 4
Samsung Galaxy S Blaze 4G Start Manual preview
Galaxy S Blaze 4G
Brand: Samsung Pages: 27
Samsung Galaxy S 4 mini Getting Started Manual preview
Galaxy S 4 mini
Brand: Samsung Pages: 26
Samsung GALAXY S GT-I9000 User Manual preview
GALAXY S GT-I9000
Brand: Samsung Pages: 132
Samsung Galaxy S Aviator Quick Reference Manual preview
Galaxy S Aviator
Brand: Samsung Pages: 56
Samsung Galaxy Note20 Ultra 5G Quick Start Manual preview
Galaxy Note20 Ultra 5G
Brand: Samsung Pages: 2
Samsung Galaxy Note20 5G Quick Reference Manual preview
Galaxy Note20 5G
Brand: Samsung Pages: 2
Samsung Galaxy Note II Get Started preview
Galaxy Note II
Brand: Samsung Pages: 41
Samsung Galaxy Note 9 Settings Manual preview
Galaxy Note 9
Brand: Samsung Pages: 2
Samsung Galaxy Note 8 Quick Reference Manual preview
Galaxy Note 8
Brand: Samsung Pages: 28
Samsung Galaxy Note 8 Basic Manual preview
Galaxy Note 8
Brand: Samsung Pages: 65
Samsung GALAXY MEGA How To Use The 2 Sim Cards preview
GALAXY MEGA
Brand: Samsung Pages: 7
Samsung GALAXY ON5 User Manual preview
GALAXY ON5
Brand: Samsung Pages: 109
Samsung GALAXY Note 8.0 Repair Manual preview
GALAXY Note 8.0
Brand: Samsung Pages: 51
Samsung Galaxy S III Get Started preview
Galaxy S III
Brand: Samsung Pages: 36
Samsung Galaxy S III Important Information Manual preview
Galaxy S III
Brand: Samsung Pages: 68
Samsung GALAXY Young Quick Start Manual preview
GALAXY Young
Brand: Samsung Pages: 17
Samsung OFFICESERV 100 Series System Administration & Special Features Manual preview
OFFICESERV 100 Series
Brand: Samsung Pages: 22

Brands by name

Popular brands

Load more brands