Matrix SPARSH VP710 User Manual Download Page 482

Page: 482 / 1046

474

Matrix SPARSH VP710 User Guide

Procedure

Configuration changes can be performed using the configuration files or locally.

Configuration File

<MAC>.cfg

Configure subscribe for MWI.

Configure subscribe MWI to voice mail.

Configure the voice mail number on a

per-line basis.

Configure the presentation of audio
and visual MWI.

For more information, refer

“Appendix

D - Configuration Parameters”

Local

Web User Interface

Configure subscribe for MWI

Configure subscribe MWI to voice mail.

Configure the voice mail number on a

per-line basis.

Configure the presentation of audio
and visual MWI.

Navigate to:

http://<phoneIPAddress>/
servlet?m=mod_

data&p=account-adv&q=load&acc=0

Phone User Interface

Configure the voice mail number on a

per-line basis.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands