Matrix SPARSH VP710 User Manual Download Page 330

Page: 330 / 1046

322

Matrix SPARSH VP710 User Guide

The number of the DSS keys associated with an account in case of SPARSH VP710 can be less than or equal to
27.

The following shows two line keys associated with a registered account 1037:

Procedure

Multiple line keys per account can be configured using the following methods.

Configuration File

<MAC>.cfg

Configure auto linekeys.

Configure the number of DSS keys

to be assigned automatically.

For more information, refer

“Appendix

D - Configuration Parameters”

Local

Web User Interface

Configure auto linekeys.

Navigate to

http://<phoneIPAddress>/servlet?m
=mod_data&p=features-general&q
=load

Configure the number of DSS keys

to be assigned automatically.

Navigate to

http://<phoneIPAddress>/servlet?m

=mod_data&p=account-adv&q=loa

d&acc=0

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands