Matrix SPARSH VP710 User Manual Download Page 154

Page: 154 / 1046

146

Matrix SPARSH VP710 User Guide

•

Click

Confirm

to save the change.

A dialog box pops up to prompt that the settings will take effect after a reboot.

•

Click

to reboot the phone.

You can adjust the following volume level using the phone:

•

Ringer volume:

Press the Volume key to adjust the ringer volume when the phone is idle or ringing. When

adjusting ringer volume, the touch sound and notification sound volume will change as well.

•

Talking volume:

Press the Volume key to adjust the receiver volume of currently engaged audio devices

(handset, speakerphone or headset) when the phone is in use.

•

Key tone volume:

Press the Volume key to adjust the key tone volume when the phone is on the dialing

screen.

•

Media volume:

Press the Volume key to adjust the media volume when playing audios/videos.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands