Matrix SPARSH VP710 User Manual Download Page 855

Page: 855 / 1046

Matrix SPARSH VP710 User Guide

847

Range

0 - Disabled

1 - Enabled

Example

account.X.sip_server.Y.register_on_enable= 0

Parameter

account.X.outbound_proxy_enable

(X ranges from 1 to 16)

Configuration File

<MAC>.cfg

Description

Enables or disables the IP phone to send requests to
the outbound proxy server for account X.

Default Value

Range

0 - Disabled

1 - Enabled

Example

account.X.outbound_proxy_enable = 0

Parameter

account.X.outbound_proxy.Y.address

(X ranges from 1 to 16, Y ranges from 1 to
2)

Configuration File

<MAC>.cfg

Description

Configures the IP address or domain name of the
outbound proxy server Y for account X.

Note:

It works only if the value of the parameter

“account.X.outbound_proxy_enable” is set to 1
(Enabled).

Default Value

Blank

Range

IP address or domain name.

Example

account.1.outbound_proxy.1.address =

10.1.8.11

Parameter

account.X.outbound_proxy.Y.port

(X ranges from 1 to 16, Y ranges from 1 to
2)

Configuration File

<MAC>.cfg

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Matrix SPARSH VP710, User Manual, Page: 855 / 1046

Search results

Summary of Contents for SPARSH VP710

Reviews: