manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

14

Matrix SPARSH VP710 User Guide

LED Instructions

Power Indicator LED

Camera Indicator LED

The above table displays the default LED status. The status of the power indicator LED is configurable via 
web user interface. Refer 

“Power Indicator LED”

 for details.

LED Status

Description

Solid red

The phone is initializing.

Fast flashing red 

The phone is ringing.

Slow flashing red 

The phone receives video/ voice mail.

Off

The phone is powered off

.

The phone is busy.
The phone is idle.
The call is placed on hold or is held.
The call is mute.

LED Status

Description

Solid green 

The phone is powered on and the camera is properly 
connected to the phone. 
The camera is idle. 
The phone receives an audio-only call. 

Flashing green 

The phone receives a video call. 

Solid red 

There is an active video call. 
The video call is muted. 
The video call is held.
 

Slow-flashing red 

The shutter switch is open, but the near-site video is stopped 
transmitting during a video call. 
The video call is placed on hold. 

Off 

The phone is powered off. 
The camera is not properly connected to the phone. 
The shutter switch is closed. 

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Samsung Galaxy TAB4 Manual preview
Galaxy TAB4
Brand: Samsung Pages: 38
3Com VCX V7000 Manager'S Manual preview
VCX V7000
Brand: 3Com Pages: 118
3Com CoreBuilder 3500 Manual preview
CoreBuilder 3500
Brand: 3Com Pages: 92
Airbus Tactilon Dabat User Manual preview
Tactilon Dabat
Brand: Airbus Pages: 123
Pantech Laser Guía Del Usuario preview
Laser
Brand: Pantech Pages: 97
Pantech Laser Getting Started Manual preview
Laser
Brand: Pantech Pages: 52
Pantech Laser Quick Start Manual preview
Laser
Brand: Pantech Pages: 2
i-mobile i651 User Manual preview
i651
Brand: i-mobile Pages: 99
jablotron JA-65X Installation Manual preview
JA-65X
Brand: jablotron Pages: 7
Avaya one-X 4610SW User Manual preview
one-X 4610SW
Brand: Avaya Pages: 84
Allview P7 Xtreme User Manual preview
P7 Xtreme
Brand: Allview Pages: 143
Shenzhen JR168-900 User Manual preview
JR168-900
Brand: Shenzhen Pages: 57
ATCOM AT-620 User Manual preview
AT-620
Brand: ATCOM Pages: 60
Doro HANDLEPLUS 326I GSM Manual preview
HANDLEPLUS 326I GSM
Brand: Doro Pages: 280
Pantech ADR910L User Manual preview
ADR910L
Brand: Pantech Pages: 213
Infinix X665B User Manual preview
X665B
Brand: Infinix Pages: 7
PCD PH5003 User Manual preview
PH5003
Brand: PCD Pages: 16
ORANGE RIO II User Manual preview
RIO II
Brand: ORANGE Pages: 88

Brands by name

Popular brands

Load more brands