Matrix SPARSH VP710 User Manual Download Page 733

Page: 733 / 1046

Matrix SPARSH VP710 User Guide

725

•

static.syslog.bootlog_upload_wait_time

-- Specify the waiting time before the phone uploads the log

file to the provisioning server.

•

static.auto_provision.server.url

-- Specify the access URL of the syslog server or provisioning server.

Configuring the Severity Level of the Log

Procedure

Severity level can be configured using the configuration files or locally.

To configure the level of the system log via web user interface:

Configuration File

<MAC>.cfg

Configure the severity level of the
logs to be reported to a log file.

For more information, refer

“Appendix D - Configuration
Parameters”

Local

Web User Interface

Configure the severity level of the
logs to be reported to a log file.

Navigate to

http://<phoneIPAddress>/
servlet?m=mod_data&p=settings-
config&q=load

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Matrix SPARSH VP710, User Manual, Page: 733 / 1046

Search results

Summary of Contents for SPARSH VP710

Reviews: