manualshive.com logo in svg

Matrix SPARSH VP710, User Manual, Page: 768 / 1046

Share
Download
Matrix SPARSH VP710 User Manual Download Page 768

760

Matrix SPARSH VP710 User Guide

Parameter

-

static.network.internet_port.mask

Configuration File

<MAC>.cfg

Description

Configures the subnet mask when the Internet port 
type is configured as Static IP Address and the IP 
address mode is configured as IPv4 or IPv4&IPv6.

Note:

 If you change this parameter, the IP phone will 

reboot to make the change take effect.

Default Value

Blank

Range

Subnet Mask

Example

static.network.internet_port.mask = 255.255.255.0

Parameter

-

static.network.internet_port.gatewa
y

Configuration File

<MAC>.cfg

Description

Configures the default gateway when the Internet port 
type is configured as Static IP Address and the IP 
address mode is configured as IPv4 or IPv4&IPv6

.

Note

: If you change this parameter, the IP phone will 

reboot to make the change take effect.

Default Value

Blank

Range

IPv4 Address

Example

static.network.internet_port.gateway = 192.168.1.254

Parameter

-

static.network.primary_dns

Configuration File

<MAC>.cfg

Description

Configures the primary IPv4 DNS server.

Note

: It works only if the value of the parameter 

"static.network.static_dns_enable" is set to 1(On). 

If you change this parameter, the IP phone will reboot 
to make the change take effect.

Default Value

Blank

Range

  

IPv4 Address

Example

static.network.primary_dns = 202.101.103.55

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments