Matrix SPARSH VP710 User Manual Download Page 667

Page: 667 / 1046

Matrix SPARSH VP710 User Guide

659

•

EAP-FAST (requires CA certificates)

Procedure

802.1X authentication can be configured using the configuration files or locally.

To configure the 802.1Xauthentication via web user interface:

•

Click on

Network->Advanced

•

In the

802.1x

block, select the desired protocol from the

802.1x Mode

list.

•

If you select

EAP-MD5

•

Enter the username for authentication in the

Identity

field.

Configuration File

<MAC>.cfg

Configure the 802.1X authentication.

For more information, refer

“Appendix D - Configuration
Parameters”

Local

Web User Interface

Configure the 802.1X authentication.

Navigate to

http://<phoneIPAddress>/servlet?

m=mod_data&p=network-adv&q

=load

Phone User Interface

Configure the 802.1X authentication

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Matrix SPARSH VP710, User Manual, Page: 667 / 1046

Search results

Summary of Contents for SPARSH VP710

Reviews: