Matrix SPARSH VP710 User Manual Download Page 833

Page: 833 / 1046

Matrix SPARSH VP710 User Guide

825

Multicast Paging

Sending RTP Stream

Parameter

account.X.display_mwi.enable

(X ranges from 1 to 16)

Configuration File

<MAC>.cfg

Description

Enables or disables the IP phone to present audio
and visual MWI when receiving new voice

messages.

Note:

It always works at the time of Unsolicited

MWI; at the time of solicited MWI, MWI
subscription feature should be configured in
advance. To present audio MWI, you also need

to set the value of the parameter
“features.voice_mail_tone_enable” to 1 (Enabled)
in advance.

Default Value

Value

0-Disabled

1-Enabled

Example

account.1.display_mwi.enable=

Parameter

multicast.codec

Configuration File

<MAC>.cfg

Description

Configures the codec of multicast paging.

Default Value

G722

Range

PCMU

PCMA

G729

G722

Example

multicast.codec = G722

Parameter

multicast.paging_address.X.ip_address

(X ranges from 1 to 31)

Configuration File

<MAC>.cfg

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands