Matrix SPARSH VP710 User Manual Download Page 470

Page: 470 / 1046

462

Matrix SPARSH VP710 User Guide

The following table lists where the IP phone obtains the IPv6 address and other network settings:

Procedure

IPv6 can be configured using the configuration files or locally.

DHCPv6

SLAAC (ICMPv6)

How the IP phone obtains the IPv6 address and network
settings?

Disabled

You have to manually configure the static IPv6 address and
other network settings.

Disabled

Enabled

The IP phone can obtain the IPv6 address via SLAAC, but the
other network settings must be configured manually.

Enabled

Disabled

The IP phone can obtain the IPv6 address and the other
network settings via DHCPv6.

Enabled

The IP phone can obtain the IPv6 address via SLAAC and
obtain other network settings via DHCPv6.

Configuration File

<MAC>.cfg

Configure the IPv6 address
assignment method.

Configure the IPv6 static DNS
address.

Configure the IPv6 static DNS.

For more information, refer

“Appendix D - Configuration
Parameters”

Local

Web User Interface

Configure the IPv6 address

assignment method.

Configure the IPv6 static DNS.

Navigate to:

http://<phoneIPAddress>/servlet?m=

mod_data&p=network&q=load

Phone User Interface

Configure the IPv6 address

assignment method.

Configure the IPv6 static DNS.

Configure the IPv6 static DNS address

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands