Matrix SPARSH VP710 User Manual Download Page 459 | Manualshive

Page: 459 / 1046

background image

Matrix SPARSH VP710 User Guide

451

Hide Feature Access Codes

This feature enables the IP phone to display the feature name instead of the dialed feature access code
automatically.For example, the dialed call park code will be replaced by the identifier “Call Park” when you park an
active call.

The feature is applicable to the following features:

•

Voice Mail

•

Pick up

•

Group Pick up

•

Barge In

•

Retrieve

•

Call Park

•

Call Pull

Procedure

Hide feature access codes feature can be configured using the configuration files or locally.

Configuration File

<MAC>.cfg

Configure the hide feature access codes
feature.

For more information, refer

D - Configuration Parameters”

.

Local

Web User Interface

Configure the hide feature access codes
feature.

Navigate to:

http://<phoneIPAddress>/servlet?m
=mod_data&p=features-general&q

=load

«
...
457
458
459
460
461
...
»

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Brand: Samsung Pages: 38

Brand: TCL Pages: 52

Brand: Ecom Instruments Pages: 64

Brand: H-TEK Pages: 142

Brand: FLY Pages: 48

Brand: Avaya Pages: 172

Brand: Uclear Pages: 36

Telenium IP IP7008D

Brand: Vodavi Pages: 2

OPENTOUCH ALE-300

Brand: Alcatel-Lucent Pages: 101

Brand: Grandstream Networks Pages: 1

Brand: SoftBank Pages: 352

SGH-T519 - Trace Cell Phone

Brand: Samsung Pages: 141

Brand: Samsung Pages: 178

Brand: Samsung Pages: 174

Brand: Samsung Pages: 105

Brand: Zte Pages: 96

Brand: Nokia Pages: 23

Brand: Nokia Pages: 121

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands